February 7, 2018

Ikea Children's {Poang} Chair Makeover

So over the course of the past year, we've accumulated 3 of these Children's Ikea Poang chairs. The problem.. the covers were washed without following the precise instructions, and SHRUNK. Ikea doesn't sell the separate covers, and I didn't want more of the chair frames, so I decided to do simply make new cushions & covers! 

As you can see, badly shrunken! 
First things first, I measured the back of the chair and cut 1" foam (purchased from Joanns). I ended up cutting mine 35" x 14.5". 
Then I cut the material I chose (an upholstery fabric) about 1.5" wider than the foam measurements to account for seam allowance and the depth of the foam. In hindsight, I should have cut it at maybe only 1" wider, because the cover was a tad bit baggier than I would have liked. 

I chose to recreate the original seat pad idea that simply has a "pocket" along the top back of the chair that slips over the chair itself to hold the pad on. I cut pieces the same width of my fabric, and 6" long. 
I did a double fold hem to make sure they looked finished. 

Then I laid my pieces out and pinned. I laid one of the first large pieces, right side up. Then placed the "pocket" right side up on top of that, with the hemmed section down - so that the unfinished sections would all be caught up in my sewing of the perimeter. 
Then I laid the second large piece, right side down on top & pinned around 3 edges. 

Here you can see the sandwiched layer that includes the pocket. 

I used 0.5" seam allowances for the entire project. 

Once I had sewn around 3 sides, I turned the piece right side out, taking care to fold the pocket onto the correct side so that the right side of the fabric showed. 

Then I stuffed the foam in and set it down to give it a test fit. 
Here's where you can see some of the bagginess I mentioned above. I wish I had simply gone back through with a larger seam allowance to create a nicer fit. 

But oh well, hindsight is 20-20, right? 

Then I added 1 row of top stiching down the middle of the foam cushion to help ensure that it would not slip and slide around while being used. 
Again, in hindsight, I probably would have added 2 more vertical lines on either side - and honestly, I still may! 
It's also a little hard to tell, but I also sewed a horizontal line where the seat back and seat cushion meet. It was one continuous piece of foam, but I wanted to create a "hinge" point to help the cushion sit neater on the frame. 

Next, I folded the end material around the edge of the chair to see how much slack I had. The original chair design includes velcro along the bottom edge for the cover to be attached too. I did a quick folded measurement to make sure I was appropriately reaching the foam. 

Then I cut off excess material (I had not measured the length too carefully while cutting because I knew the extra pieces would not be significant.) 
Then I folded the edges in to give it a more streamlined look from the front/sides. 
And then folded the hem down to make it look finished. 1 Quick top stitch along that hemmed edge and I was almost finished!

I happened to have some iron on velcro at the house in a neutral color, so I went ahead and used it! I cut pieces to cover the entire edge and followed ironing instructions to attach. 

I tried to make a head cushion like the original chair included...but that did not turn out too well! I couldn't figure out how to get it to lay down flat. So I ended up ditching the idea for now! 
And viola! The cover is done! Certainly not perfect, but a bit cushier and nicer looking than what we had! :) 

Next - a repainting of the frames! One of the chairs we got is already pink, but the other two are natural wood, and a bit dirty! 

Thank you for reading! Let me know if you have any questions! I'll do my best to answer. :) 

March 19, 2017

Painted {Honeycomb} Accent Wall

So now that our downstairs craft room is OK to be inhabited (water leaks repaired and electricity turned back on), I'm getting so excited about moving all of my craft room & office things down there to have more SPACE for my projects! Before I did that, though, I knew I wanted to give the walls and floor an upgrade! Off to pinterest I went, OF COURSE.

My criteria were:

Bright -there's only the one small window, and the lights aren't great either, so I didn't want to risk adding any dark colors on the wall that would make the space darker or seem smaller.
Colorful - Our whole house has these kind of taupe, off-white, BORING wall colors. I haven't really been motivated to take on the task of repainting them all, so since I knew I was going to repaint this room, I knew I wanted it to be a fun and pretty color that I would love.
Fun/Inspirational/Motivational - I really loved how our first "craft room" was SO bright with natural light and had bright green walls, and I wanted to mimic that same fun mood, even though I'm technically in a basement.

I saw a few fun ideas like chevron walls, diamonds,  herringbone...and then I saw it. A HONEYCOMB/Hexagon wall (like this).

And I was hooked.

I knew I wanted to do one on one of the walls... but then came the big decisions: What colors to use? How big? Which wall? Who would help me....? :) It took me a few weeks of internal deliberating to finally work up the courage to just go into home depot and pick up a color and get to work.

As my Christmas present, my brother had volunteered his time to come help me paint, so once I picked out the main color (a pretty light green - in homage to my "Green Room") he came and helped me paint the 3 solid walls. :) Yay! I also did a base coat of clean fresh white on the wall I decided to use as my accent wall. Even just having all that finished made the room look so new and clean! Then the following weekend, I drafted my sister to help with the accent wall, AND my cousin was in town visiting, and offered to help as well. I felt pretty dang lucky to not be doing it by myself! :)

First things first, we had to figure out the math involved with drawing hexagons... Luckily my Aunt stuck around for this part, because otherwise we would've been hitting up our ole' friend Google.
In case you're curious, there are 360 degrees total, and we needed 6 angles, so a simple 360/6=60. Then it was a matter of finding a protractor, and remembering how to use it! 😁
We drew it out on regular cardboard, cut it with a utility knife, and then I ended up taping around the edges to give a smoother edge to work against. We double sided painters tape on the back to hold it steady while we were taping around it. :)

Then came the fun part - sticking it to the wall and taping around. OVER AND OVER again. I haven't counted the hexagons, but maybe I will.. haha

^^ We enlisted all the help we could get!

And before I show you more progress, I'll give you some tips for doing this taping off! A) A packing tape gun! My aunt had this idea, and it worked SO nicely.

We didn't actually press it against the wall like you would with a box, but it held the "open" edge so we didn't keep losing it, and provided a quick and easily accessible cutting surface without having to mess with scissors! I definitely recommend one if you're going to try a similar tape heavy project!

We also found that less it more when you're taping the borders of the hexagons. Because each corner is a meeting of 3 different strips of tape, it's better to slightly underestimate the tape length you need than to overestimate.
We over-estimated a few times and ended up having to go back through and carefully cut & peel away all the edges with the utility knife.
My sister having SO much fun trimming all the parts that were too long. 
Here's what I mean, in a bit more detail. 

Tape your first edge

Leave some overhang on either side - but you don't want it to be longer than the width of your tape. 

Line up your next piece of tape, making sure not to pass the width of your previous piece. 

This is what NOT to do. ;) 

If your piece is a little short, you're OK to use it, as long as the tape meets where my finger is - giving your hexagon the appropriate corner at this junction. 

Keep going like this all the way around your first hexagon. 

Then when you start your subsequent hexagons, you already have at least one edge done. Line your template up so the corners of the template look pretty straight when compared to the corners of your previously taped hexagon. (Both on the sides as applicable, and up/down as applicable.) 

Then just start taping around it like you had done on the first. 

This is an example of a piece that was too long - it passed the outer edges of the tape on these two hexagons, and is encroaching on what will be the inner edge of the hexagon between/below these two. 

Use a utility knife to carefully cut along both edges to get your proper angle/edge back. 
Basically you just do that over and over again until you get them ALL done. Even while we were taping I hadn't decided exactly how many I wanted to do, or how I wanted it to look. So we decided to do the entire top half of the wall, and then see what it looked like and if/where we wanted to add more.

After finishing the top half I decided I certainly did NOT want to have an entire wall full, but thought having some "dripping" down would be kind of neat! (Note: this were a little harder to keep straight, but if we had stepped back and eye-balled the placement before taping each one it wouldn't have been too bad. We didn't think to do that, so some of my "drips" are a little skewed, BUT I don't really think it messes with the look of this wall - if you're going for something super straight, just be a bit more cautious.) 

Then, after we finished taping, we started painting right away. 


This makes me sad to think about only because we didn't stop for a minute and double check that all our tape was really pressed down well - and we ended up with leakage that could have easily been avoided. Never again will I forget! lol (Learn from my mistakes!)

 I started by dotting on some of the colors so my sister & cousin knew where to start painting, 
For my accent colors, I gathered up the colors I liked from my oops paint selection. (Home Depot's discounted colors). I ended up with some blues/teals/pinks/corals.
As for layout, I really just tried to go for an "organized random", so that they were pretty well spaced with natural looking gaps.  I had also originally planned on painting all the hexagons in these accent colors, but decided against that when we were painting when I saw how cute it was looking, and reminded myself that "Less is more". :D 
Then the last bit of painting was doing the bottom half of the wall, and the empty hexagons in the light green color to match the rest of the room. I like that they pull in the light green, but they're still surrounded by the fresh white border and all the fun colors. 

All taped & painted - ready for the big reveal! 

Then came the moment of truth.... dun dun duuuuuunn

Ripping off all the tape. 

Did you catch the word, ALL? 

5pieces of tape x 10000 hexagons... lol - Sometimes I'd get lucky and get a cluster that would stay together, but a lot of them had to be pulled off as individual pieces, so that wasn't super fun, BUT the joy of starting to see the finished product shine from underneath the paint was well worth it! 

And here it is! 

Love Love Love. 

I still need to figure out the best process for touching up the spots in the white that got dribbled on, but overall I'm SO happy with how it turned out! 

Can't wait to craft and create in this room! 

Let me know if you have any questions or need better/further explanations of any of our processes! 

February 28, 2017

When someone else's {Trash} is your {Treasure}

So, my dad has always been a bit of a pack-rat... and that makes me both LOVE finding things that others consider garbage, and also makes me a little worried about how much I love it. 😂
Anyway, M & one of his brothers picked up a bed that his brother and his wife had found on Craigslist, and while they were there, the lady offered them this old rough stool. M called me and asked and I figured I could use it either in our living room as a piano bench, in our bedroom at the end of our bed, or in the dining room at our table. 

 Flash forward a few months (when I finally remembered to bring it inside, and gave it some time to dry out) and I started work! First things first, a GOOD deep sanding. I used a 60 grit paper first to scrape off the moss (I'm not kidding), and then used my 150 grit paper for a more fine sanding.

 Then, as usual, I stressed a little about what exactly I wanted to do from here! I got some help from my friends on instagram (you know who you are!) and decided to stain the legs a dark brown and add an upholstered top with the leaf table cloth I had gotten on clearance for $5.

 So off to Joanns we went for 2" thick upholstery foam (I think it ended up costing around $15). They will cut it down length wise, but not width wise, so I did that with my own scissors once we got home.
 Next, I added in end pieces with some scrap 1x4" boards to make the whole top section uniform in shape (for covering).

 Then I stained the legs. Oh gosh. I LOOOVE the color they turned out! Then I really struggled with whether or not I should still cover the top, or if I should just stain it beautiful brown and be done.... But it really wasn't comfortable to sit on as it, so I figured I should continue with my original plan!
 (But let's just soak in this beautiful color for just a few moments, first.)

 Ok, on to the upholstery! I laid the foam down directly on the wood, and then layered a few pieces of quilt batting that I had in my piles on top to add a bit more cush, and also to add some softness along the "face" edges of the bench. I flopped the biggest piece over the top as the last step, and then folded the sides up into 1/3rds to add more cushion along the side.

 Then I pulled it snug and stapled it down to the bottom edge of the bench.
 All the way around... 100000 staples later. :) I kept making sure that I was pulling it snug across the top of the bench to make sure there were no wrinkles that we'd have to see later.

 The ends were a little complicated, but I just tried to keep it as tight as possible and cut away some of the bulk of the corners.
 Here's a better visual of the sandwiched foam between the batting and the bench top.
 All done! :)

 Those legggggss! :D *dreamy eyes*
 Then I got to work the next day on attaching the actual fabric itself. I used a similar process, but I pulled the fabric over and around the edge to staple it to the backside of the "face" plates.
(And shame on me, I didn't sand the bottom of the bench itself. It seemed like too much work for little reward- but now I'm annoyed that it's on my blog post. Hahaha)
 Again, the ends were a little weird, but I simply cut down as much bulk as possible and pulled it back tight before stapling. I added a little hot-glue to the edges after stapling to help hold the furthest pieces down past where they were being secured by the staples.
 And then it was done! Super happy with how it turned out! :)
The last thing I'll need to do is to add two quick support beams between the legs and the foot plate to add some stability. :)

Let me know if you have any questions!